User Tools

Site Tools


Sidebar

Introduction

* Home

Documentation & help

LibreCAD Community

Help on DokuWiki

Temporary shorcuts

usage:line

LINE

LINE: 2 Points

  • click the icon
  • specify first point (left-click)
  • specify second point
  • Right-click to 'back' or press 'Esc' to exit.

2 points with more detail (tips for drawing a specific length of a line; type the BOLD one into command-line).

  • specify the First point (left-click).
  • @50<0 for straight line.
  • @50,50 for Square or @50,30 for Rectangle.
  • @60<120 for 60mm line at 120 degrees. (try {-} (minus) symbol before 'degree' and see what happen!!)

LINE: Angle

  • click the icon
  • enter angle (see 'tool option')
  • enter length
  • specify start, middle, or end snap point
    • specify position
  • Right-click to 'back' or press 'Esc' to exit

LINE: Horizontal

  • click the icon
  • enter length
  • specify start, middle, or end snap point
    • specify position
  • Right-click to 'back' or press 'Esc' to exit

LINE: Vertical

  • click the icon
  • enter length
  • specify start, middle, or end snap point
    • specify position
  • Right-click to 'back' or press 'Esc' to exit

LINE: Rectangle

  • click the icon
  • specify first corner
  • specify second corner
  • Right-click to 'back' or press 'Esc' to exit

LINE: Parallel through point

  • click the icon
  • select entity
  • specify through point (click at specific point or anywhere to repeat the process)
  • Right-click to 'back' or press 'Esc' to exit

LINE: Parallel

  • click the icon
  • enter the distance and number of copies required OR
    • select entities and repeat it as required
  • Right-click to 'back' or press 'Esc' to exit

LINE: Bisector

  • click the icon
  • enter length and number (from tool option)
    • select first line
    • select second line
  • Right-click to 'back' or press 'Esc' to exit

LINE: Tangent (P,C)

  • click the icon
  • specify point
  • select circle, arc or ellipse
  • Right-click to 'back' or press 'Esc' to exit

LINE: Tangent (C,C)

  • click the
  • select first circle or ellipse
  • select second circle or ellipse
  • Right-click to 'back' or press 'Esc' to exit

LINE: Tangent Orthogonal

  • click the icon
  • select a line
  • select circle, arc or ellipse
  • Right-click to 'back' or press 'Esc' to exit

LINE: Orthogonal

  • click the icon
  • select line
  • select circle, arc or ellipse
  • Right-click to 'back' or press 'Esc' to exit

LINE: Relative Angle

  • click the icon
  • enter angle and length
    • select base entity
    • select position
  • Right-click to 'back' or press 'Esc' to exit

LINE: Polygon [(Cen,Cor), (Cen,Tan), (Cor,Cor)]

  • click the icon
    • enter number of sides as required
      • specify center
      • specify corner
  • click the icon
    • enter number of sides as required
      • specify center
      • specify tangent
  • click the icon
    • enter number of sides as required
      • specify first corner
      • specify second corner
  • Right-click to 'back' or press 'Esc' to exit

usage/line.txt · Last modified: 2020/06/18 07:31 by dushyantvyasg007